Replacement 220V Transformer for SpaGuts brand Electronic
Controllers. This transformer is for a 220V 3-Wire application that does
not use a Neutral Wire. The primary input wires are white and ... More
Replacement Spa Builders topside panel KIT, LX 10, 4-Button, Alpha, Revision 5.31. This
topside panel has a peanut shape overlay, comes with a 6ft cable and uses an 8 conductor phone-type plug. ... More
Spa rated GFCI Load Center, 50A, Culter-Hammer® Series, Eaton Model, Type BR, 50A, with Self Test. This kit comes complete with a powder coated steel box (outdoor rated), 50 Amp GFCI breaker, and ... More
Replacement mechanical time clock for many brands of spa controllers. OEM part number INTPB913N25. This time clock has a 4-pin
plug. Electrical rating is 20A, 110V, 1HP, 1800W. Clock Motor is rated ... More
If you have a pneumatic (air) spa controller with HEATER but would like the convenience of being able to not only control the temperature from a topside control unit, but to also see an LED display ... More
7-Mode Topside Command Center with display for the HRC system by TecMark. Rated 110V, 3-Button configuration with 6ft power cord and 6ft temperature sensor. OEM part number CC3D-120-061-07 and ... More
7-Mode Topside Command Center with display for the HRC system by TecMark. Rated 220V, 4-Button configuration with 6ft power cord and 6ft temperature sensor. OEM part number CC4D-240-06B-07 and ... More
Replacement Balboa M7 Sensor Kit. OEM part numbers 53605 and 32016. This sensor kit includes
one 24-inch M7 heater sensor, plastic compression nut, washer, and
o-ring. The sensor bulb is 1/4-inch ... More
The Hydro-Quip CS800-A2 Model Pneumatic Spa Controller with heater is a basic control unit.
Rated 110V, and includes a 15 feet corded 15A 110V GFCI.
It has a built-in Full Range Thermostat, and ... More
Replacement temperature sensor for SpaGuts brand CS-Series Electronic and
M-Series Controller models CS6200, CS6207, CS6230, CS6237, CS9700 and CS9707. Available in 10ft and 25ft (approx.) cable ... More
The Hydro-Quip CS800-C2 Model Pneumatic Spa Controller with heater is a basic control unit.
Rated 220V Input, 220V Pump 1 Circuit, 110V Blower Circuit, and 220V Ozone Circuit.
It has a built-in ... More
Grasslin brand Time Clock, 24HR, 220V, 16A, 60Hz. OEM part number FM/1 STUZ-L. This time clock can be used on
any spa controllers that requires a similar replacement. Normally used on 220V-240V ... More
Gecko Lite Streme Bath Control with Topside Kit. This kit includes the LS-120 Module, OEM part number 0101-200023, with 20 minute time out. This item comes with a 3ft power cord with Nema plug that ... More
Replacement Vita Spa Topside Panel, model L200, Selectron 200, 6-button,
with LCD display. OEM part number 460086. Attached is a 5ft cable with phone-type plug. Normally
used in 1998-2001 model ... More
This control unit operates via an air switch. Press the air switch button and the pump will run for 10 minutes, then automatically shut off. Press the button again for 10 more minutes of operation. ... More
Replacement Gecko Spa Controller for the S-Class type spa controllers that uses a remote heater. Model SC-MP-P121-P211-01-CP1-NE-LS-HR-JJC-SBD1. OEM part number 0202-205209. This controller does ... More
TecMark Heat Recovery Controller, Model HRC2009-120, rated 110V 15A 60Hz, built-in 3-hour time delay. This Controller includes a 12ft 15A GFCI cord and Hi-Limit Sensor. Attached to the controller ... More
The Len Gordon FF-1094TC Series control offer reliable On/Off control of
two pieces of equipment with one air button, from up to 150 feet (depend
on air button type and size of air hose). The ... More
All electrical and plumbing parts we sell are intended for installation by a licensed electrician or licensed contractor.
Any sales or technical advise provided by this site or our staff may not be construed to authorize or suggest
anything but professional installation.