Waterway Hi-Flo Model, 48-frame, 2-speed, Spa Pump in a range of sizes from 1.0 horsepower to 4.0
horsepower.
NOTE 1: The pump photo shown to the right does not show a capacitor mounted on top of the motor. We cannot guarantee if the motor that is shipped will or will not have the capacitor attached on top of the motor. Make sure there is plenty of room under the spa for a motor with 6 inches long x 2.5 inches tall x 2.25 inches wide capacitor on top of the motor.
SpaGuts P/N:
- 15-350-2110, 1.0 HP SPL 9.5-11.0/2.9-3.2A, 115V, SD
- 15-350-2120, 1.0 HP SPL 9.5-11.0/2.9-3.2A, 115V, CD
- 15-350-2130, 1.5 HP SPL 13.5-16.4/4.4A, 115V, CD
- 15-350-2140, 1.5 HP SPL 13.5-16.4/4.4A, 115V, SD
- 15-350-2150, 1.5 HP SPL 6.5-8.0/2.6A, 230V, CD
- 15-350-2160, 1.5 HP SPL 6.5-8.0/2.6A, 230V, SD
- 15-350-2170, 2.0 HP SPL 8.4-9.0/2.8A, 230V, CD
- 15-350-2180, 2.0 HP SPL 8.4-9.0/2.8A, 230V, SD
- 15-350-2190, 3.0 HP SPL 10.5/2.6A, 230V, SD
- 15-350-2195, 4.0 HP SPL 12.0/3.5A, 230V, SD
NOTE 2: The 1.0HP motors are only available in 110V, and the 1.5HP motors are available
in either 110V or 220V. Motors larger than 1.5 HP must be 220V.
NOTE 3: Amp rating and dimensions may vary depending on the motor brand and model that is used with this pump. Motor brand can be US Motors, AO Smith Century Laser, GE, Etc... Please contact us to verify dimensions if space is very limited for the new pump.
Pumps with 48-frame motors can be ordered with "SIDE" or "CENTER" discharge.
Center-Discharge pumps come standard with 1.5 inch fittings (outside thread measurement are approximately 2-3/8 inch). Adapters are optional for the center discharge pumps when 2.0 inch fittings are requested. Side-Discharge pumps come standard with 2.0 inch fittings (outside thread measurement are approximately 3.1 inch).
Diagrams below shows both pump discharge on top pointing to the 12 o'clock position. The pump discharge can also be rotated every 90-degrees (3, 6 or 9 o'clock positions) by loosing the four long bolts at the back of the motor. The pump intake (suction) is located in the front center face of the pump.
*Looking for a Side Discharge Pump with standard 1.5 inch threaded fittings? Click here
If buying this pump for retrofitting, add a pair of pump unions that connects to your pipes which then screws directly onto the pump threaded fittings. O-rings are included with the pump unions. Regular price is $22.95.
If buying this pump as an exact replacement that does not require retrofitting, it is highly recommended to replace the pump union o-rings at the same time. Old pump union o-rings may cause leaks that can damage the new pump and affect the warranty. O-rings for pump unions are only available with a pump union purchase.
You may add a cord to be attached to the motor at a discounted price. See cord options below.
The pump normally ships from the factory with the discharge pointing "UP" which is the standard position for shipping, but they can be turned or what is called "clocked" into any position (12, 3, 9 or 6 o'clock position). Rotation of the pump discharge can be done in the field, but we recommend having it performed by a professional spa technician who is experienced. Or choose the option to have the pump professionally rotated at the factory before it ships. This is to avoid water leaks and operational problems due to improper removal and installation in the field that will affect the warranty. As you face the front end of the pump wet end, available positions are 12 o'clock (Up), 3 o'clock (Right), 9 o'clock (Left), and 6 o'clock (Down, which is very rare).
Pumps with 48-frame motors carry a 1-Year Limited Warranty. (Starting 12/06/2017)
Keep in mind that if your pump is rated 56-frame, you might want to consider the 56-frame Pump
Click here to see water flow chart, amp rating and diagram for a Center Discharge48-frame pump.
Click here to see water flow chart, amp rating and diagram for a Side Discharge 48-frame pump.
Is Your Pump Above the Water Line?
If you need to install your spa pump near or above the waterline - as is
common for in-ground spas - you will need a pump pot.
The pump pot help prevents water from draining back
into the spa when the motor is turned off
The Center Discharge Pump is a replacement option for the following Waterway E-Series and Aqua-Flo FMCP Pump models and part numbers: 3420310-15 (3/4HP), 3420410-15 (1.0HP), 3420610-15 (1.5HP), 3420620-15 (1.5HP), 3421021-15 (2.0HP), 3420820-15 (2.0HP), 3410310-15 (3/4HP, 1SPD), 3410410-15 (1.0HP, 1-SPD), 3410610-15 (1.5HP, 1SPD), 3410830-15 (2.0HP, 1SPD, 110/220V), 02610000-1010 (1.0HP 110V), 1-00-0014 Allied (1.0HP 110V), 02610516-2 (1.0HP 110V), 02610 (1.0HP 110V), 03610000 (1.0HP 110V), 03610520 (1.0HP 110V), 02615000-1010 (1.5HP 110V), 1-00-0045 (1.5HP 110V), 02615, 02615508-2 (1.5HP 110V), 03615520-1 (1.5HP 110V), 03615487-2 (1.5HP 110V), 02615050 (1.5HP 110V), 03615001-2 (1.5HP 110V), 02615500-2(1.5HP 110V), 02615005-1010 (1.5HP 220V), 1-00-0029 (1.5HP 220V), 02615205 (1.5HP 220V), 02615020 (1.5HP 220V), 02515000-1010 (1.5HP 220V), 02520000-1010 (2.0HP 220V), 02620000-1010 (2.0HP 220V), 03620459-2 (2.0HP 220V), 03621000-2 (2.0HP 220V), 02620000-2 (2.0HP 220V), 02620000 (2.0HP 220V), 02620000-1010 (2.0HP 220V), 03620205-1 (2.0HP 220V), 03620521-1 (3.6 SPL, use 2.0HP 220V), 1-00-0043 (2.0HP 220V), 02620, 03510631-2 (1.0 or 1.5HP 110V), 03510629-2 (1.0 or 1.5HP 110V), 03621871-1 (3.6HP SPL), 02615005-1 (1.5HP, 220V), 3410410-1M6T (1.0HP 110V), 7-186095-02 (Motor Only, 3.0HP SPL), Leisure Bay 303646 (2.0HP SPL),
03610001-2 (AF FMCP 1.0HP 110V CD), 3420620-15BS, 02515515-2 (AF FMCP 1.5HP 115/230V CD; Must Confirm Motor Voltage), 91040800-000 (Wet End ONLY; Must Confirm HP and Voltage), 03610003-5 (1HP, 1.5 MBHP), Watkins Wavemaster 3000 (1.0HP 110V; Verify Wetend), 02507002-5 (0.75HP 110V w/15-Frame Motor), 03521000-2 (3HP SPL, 230V, 8.7A), 303627 (1.5HP), 303694 (3.0HP SPL), 02615084-1(1.5HP, 115V), Leisure Bay 303655 (1.5HP 230V)
Our Center Discharge Pump is also the replacement option for the "Relia-Flo" pumps by Caldera Spas. Verify motor amp rating and voltage, the pump discharge type and size fitting to match. Note that the new motor will not have the cover with heat vent connection. The original motor cover with heat vent connection may be used on the new motor if it fits, otherwise retrofitting a heat vent is required. Replacement option for the following pump model numbers: 72200, 02610183-1, 02610736-1
The Side Discharge Pump is a replacement option for the following Waterway Hi-Flo and Hi-Flo II pump model and part numbers: 3420310-15 (3/4HP), 3420410-10 (1.0HP), 3420610-10 (1.5HP), 3420620-10 (1.5HP), 3421021-10 (2.0HP), 3420820-19 (2.0HP), 3420820-10 (2.0HP), 3421221-10 (2.0HP), 3421621-10 (4.0HP), 3410410-10 (1.0HP, 1SPD), 3410612-10 (1.5HP, 1SPD), 3410830-10 (2.0HP, 1SPD, 110/220V), 3411621-10 (4.0HP, 1SPD), 3420410-H10 (1.0HP), 3420610-H10 (1.5HP), 3420620-H10 (1.5HP), 3420820-H10 (2.0HP), 3410410-H10 (1.0HP, 1SPD), 3410612-H10 (1.5HP, 1SPD), 3410830-H10 (2.0HP, 1SPD, 110/220V), 3420610-2041 (1.5HP 110V), SD-20-2N22CD, 3420610-0045 (1.5HP), SD-15-2N11CD (1.5HP), 3420610-0087 (1.5HP 110V)
Motor Models that are normally used with these pumps: F48AD44A79 (1.5HP 220V Motor), 7-182477-02 (3HP 220V Motor), 7-196012-03 (2HP 220V Motor), T55CXBLF-959 (3 OR 4HP SPL 220V, 11A Motor), 5CK38RN3818X (1.0HP 110V Motor), BN50 or 7-177803-02 (1.5HP 110V Motor), T55MWCBP-1197 (1.5HP 110V Motor), 7-196012-03 (2HP), T55CXBLF-959 (3 OR 4HP SPL 220V, 11A Motor), 5CK38RN3818X (1.0HP 110V Motor), T55MWCAT-1180 (2.0HP 220V), C55CXJAS-4344 (3.0HP, 220V), T55MWCFR-1288 (2.0HP, 220V), 7-186022-03 (1.5HP 110V), S55CXNPH7241 (1.0HP 110V Motor Only)