Whirlpool Bathtub Pumps
Failed whirlpool jetted bath tub pumps can be easily replaced with our Whirlpool bath tub pump, which fits all whirlpool bath tubs.
The Whirlpool bath tub pump is compact and easy to install. It runs quietly.
It’s also known to be the most reliable bath tub pump on the market, with a failure rate of less than
- 15-350-2271, 1/2 HP, 115V
- 15-350-2275, 3/4 HP, 115V ***OUT OF STOCK***
- 15-350-2290, 1.0 HP, 115V ***OUT OF STOCK***
- 15-350-2285, 1.5 HP, 115V ***OUT OF STOCK***
If you are replacing an existing bath tub pump, you should replace it with the same or similar
horsepower and amp rating as your existing pump, if you are happy with current forcefulness of
the water coming out of your jets. Check the motor label specifcations on the pump you are replacing. In general bath tub pump motors should have 1 HP for every 4 to 6 standard size jets. More horsepower is not better. Overpowering your jets with too much horsepower could damage your plumbing, your equipment, or even you! So, it is important to get the right sized motor for your bath tub. We offer the following horsepower levels:
- 0.5 HP 110V 5.5Amp
- 0.75 HP 110V 7.5Amp ***OUT OF STOCK***
- 1.0 HP 110V 9.5Amp ***OUT OF STOCK***
- 1.5 HP 110V 13.0Amp ***OUT OF STOCK***
For retrofitting, you have the option to add screw-on pump unions which glue directly onto 1.5 inch plumbing. After the unions are glued onto your bath tub’s existing plumbing, the unions screw directly onto the pump’s suction and return fittings. The included o-rings provide a tight seal. If buying this pump as an exact replacement that does not require retrofitting, it is highly recommended to replace the pump union o-rings at the same time. Old pump union o-rings may cause leaks that can damage the new pump and affect the warranty. O-rings for pump unions are only available with a pump union purchase.
Keep your water hot. Add a bath tub heater.
Bath Tub Heater
Bathtub Pump & Heater Controller
Prevent endless running of your pump and heater.
Bathtub Water Level Sensor
Prevent damage from spraying water. Ensure your bath tub’s water level is above the jets before
allowing the pump to run.
Bathtub Water Level Sensor
- UL and CSA safety approved for indoor operation
- 1-year limited warranty
- Quiet operation
- Compact design
- Top center discharge
- Self-draining volute
- Standard 1.5-inch fittings
- Thermally protected
- NEMA Plug with 2.5 foot cord length
- 3425 RPM
- 65, 86, 100 or 130 GPM flow rate
- 110 volts
- 5.5, 7.5, 9.5, or 13.0 Amp
- Frequency of 60Hz
- 10mm and 15mm frame size
- Built-in air switch
These bath pumps are also replacement options for the following bath pump part numbers and models: Genesis 321FF10-0150 (1/2 HP), Genesis 321HF10-0150 (3/4 HP), Genesis 321JF10-0150 (1.0HP), Genesis 321NF10-0150 (1.5HP), WOW 1010031 (1/2 HP), WOW 1050031 (1/2 HP), WOW 1010037 (3/4 HP), WOW 1010032 (3/4 HP), WOW 1050032 (3/4 HP), POWER WOW 1011014 (1.0HP), POWER WOW 1051014 (1.0HP), POWER WOW 1011057 (1.0HP), POWER WOW 1051057 (1.0HP), POWER WOW 1034002 (1.5HP), POWER WOW 1074002 (1.5HP), POWER WOW 1034019 (1.5HP), POWER WOW 1074019 (1.5HP), 97111-423 (1/2HP), 34-270-2002 (3/4HP), F42F07A03 (Motor Only, 1.5HP 9.5A), WOW PUWWS12598R (No Air Switch), WOW PUWWSCAS12598R, WOW 1010106 (No Air Switch), WOW PUWWSC12598R (No Air Switch), 752538-0070A, 202499557, 1010115, PUWWAS1298P, PUWWSCAS598R, PUUTSCAS2098R, Hydro Air Magna Series LD5MCT-C with Motor K37GWBLF-609, 73533-AA (1.0HP 11A; 2-speed; OBSOLETE), PUWWSCAS798R (0.5HP 5.5A), WCA75, WCA100, WCA150, WBA75, WBA100, WBA150, WBA200, WAA100, WAA150, WAA200, 1034100 (1.5HP), 605000UC-RS5 (6.0A), 605000UD-RS5, 97411-421 (1.5HP, 9.5A), PUUF1598 (1.5HP Wet End Only; Retrofitting Required), PUULSCAS10948BR (1.0HP), PUULSCAS10948 (1.0HP), PUULCAS7948BR (1.0HP), PUULSCAS10948GR (1.0HP), PUULSCAS10948R (1.0HP), 1014254 (1.0HP), Balboa 1034205 (1.5HP, Cord will need to be replaced with AMP and air switch bypassed), PUU3C1598R (1.5HP, Cord will need to be replaced with AMP and air switch bypassed), 01707502-2 (Aqu-Flo, 3/4 HP, Replumbing Required), Aqua Glass 1011100, 752538-300 (American Standard, 1.25HPR, 5.5A), 1010007 (5.5A)
If your tub is not already equipped with an air button, you’ll need to add
an air button to your order. The air button
comes with 4ft air tubing that connects to the air switch on the bath pump to
turn it on/off.