Executive-48 1.0HP 110V 2SPD SD Waterway Spa Pump, 2.5-inch Intake, 3420410-13 (SPECIAL ORDER, FINAL SALES, NO RETURNS)

Waterway Spa Pump, Executive 48 model, 1.0HP 110V 2-Speed Side Discharge with 2.5-inch Intake. OEM part number 3420410-13.

SPECIAL ORDER NOTES: THIS ITEM IS A SPECIAL ORDER AND HAS AN ESTIMATED 2-5 BUSINESS DAYS LEAD TIME BEFORE SHIPPING. SPECIAL ORDERS ARE NON-RETURNABLE AND CANNOT BE CANCELED ONCE THE ORDER IS PLACED.

NOTE: The pump photo shown above does not show a capacitor mounted on top of the motor. We cannot guarantee if the motor that is shipped will or will not have the capacitor attached on top of the motor. Make sure there is plenty of room under the spa for a motor with 6 inches long x 2.5 inches tall x 2.25 inches wide capacitor on top of the motor.

SpaGuts P/N: 15-350-4013

Features:

• Rated 1.0HP, 115V, 10.8/2.8A (*Amp Rating Varies)
• Dual Speed Pump (Low/High. Can also be wired for single speed)
• 2.5" center suction, and 2.0" side discharge (Outside thread measures approximately 3.5 inch for the intake, 3.1 inch for the discharge)
• UL and CUL certifications
• Equipped with the highest quality Viton Pump Seal
• Equipped with the high efficiency electrical motor and high performance pump wet end
• Includes a 1-Year limited warranty

*NOTE: Amp rating and dimensions may vary depending on the motor brand and model that is used with this pump. Motor brand can be US Motors, AO Smith Century Laser, GE, Etc... Please contact us to verify dimensions if space is very limited for the new pump.

The pump image shows the pump discharge on top pointing to the 12 o'clock position. The pump discharge can also be rotated every 90-degrees (3, 6 or 9 o'clock positions) by loosing the four long bolts at the back of the motor. The pump intake (suction) is located in the front center face of the pump.

The pump normally ships from the factory with the discharge pointing "UP" which is the standard position for shipping, but they can be turned or what is called "clocked" into any position (12, 3, 9 or 6 o'clock position). Rotation of the pump discharge can be done in the field, but we recommend having it performed by a professional spa technician who is experienced. Or choose the option to have the pump professionally rotated at the factory before it ships. This is to avoid water leaks and operational problems due to improper removal and installation in the field that will affect the warranty. As you face the front end of the pump wet end, available positions are 12 o'clock (Up), 3 o'clock (Right), 9 o'clock (Left), and 6 o'clock (Down, which is very rare).

Motor Cord options are available and sold separately.

If buying this pump for retrofitting, add a pair of pump unions that connects to your pipes which then screws directly onto the pump threaded fittings. O-rings are included with the pump unions.

If buying this pump as an exact replacement that does not require retrofitting, it is highly recommended to replace the pump union o-rings at the same time. Old pump union o-rings may cause leaks that can damage the new pump and affect the warranty. O-rings for pump unions are only available with a pump union purchase.

This pump is also a replacement option for the following part numbers: Waterway 342041A-13 Pump, Waterway 3420410-13, Waterway Model PF-10-2N11C4 (Must Confirm Ratings and Fittings to Match), Waterway 311-1210 (2.5-inch Wet End Faceplate), Waterway 315-1260 (Wet End Volute), 1-05-0313 (Impeller Only), Waterway 310-4230 (Impeller Only)

Motor models that are normally used with this type of pump: F48AD32A79R, BN37, 1-20-0002