Aqua-Flo Flow-Master XP2 48Y Spa Pump, by Gecko, 1.5 BHP, 1.0 HP Continuous, 110V, 06610006-2040 (SPECIAL ORDER)

Aqua-Flo Flow-Master XP2 Spa Pump, by Gecko.  Rated 1.5 Break Horse Power (BHP), 1.0 Horse Power Continuous (HP), 110V, 2-Speed, 60Hz, 48-Frame.  OEM part number 06610006-2040.

SPECIAL ORDER NOTES: THIS ITEM IS A SPECIAL ORDER AND HAS AN ESTIMATED 2-10 BUSINESS DAYS LEAD TIME BEFORE SHIPPING. SPECIAL ORDERS ARE NON-RETURNABLE AND CANNOT BE CANCELED ONCE THE ORDER IS PLACED.

NOTE: The pump photo shown above only shows one capacitor mounted on top of the motor. We cannot guarantee if the motor that is shipped will have 1 or Dual Capacitor attached to the outside of the motor housing, and at a specific location due to different motor models that are supplied. Make sure there is plenty of room where the spa pump is located for a motor that may have a single of dual motor capacitor on the outside of the motor housing.

SpaGuts P/N:  15-720-0062

Pump and Motor Ratings

• Pump Wet End Model: XP2
• 2.0 inch Center Suction
• 2.0 inch Side Discharge
• Horse Power: 1.0HP Continuous
• Voltage: 115V
• Amps: 10.5/3.2 (Varies by Motor)
• Frequency: 60Hz
• RPM: 3450/1725
• Speed: Dual
• Type: Indoor
• Usage: Above Ground Pool and Spa

This is a Side Discharge Pump with 2.0-inch fittings. Outside thread to outside thread measurement on the pump fittings is approximately 3.1 inches. (Pump Unions sold separately)

This Dual Speed Pump can also be wired for use as a single speed.

Dimensions (Approx): 15.75 inches long, 8.0 inches high, 7.25 inches wide.

The pump image shows the pump discharge on top pointing to the 12 o'clock position. The pump discharge can also be rotated every 90-degrees (3, 6 or 9 o'clock positions) by loosing the four long bolts at the back of the motor. The pump intake (suction) is located in the front center face of the pump.

Motor part numbers that are normally used for this pump: BN60, 7-186022-03

Also known as pump model 06610006-2.

This pump is also a replacement option for the following spa pump part numbers: Wavemaster 4000 (1.0HP), Wavemaster 6000, Watkins 37334-02 (1.0HP), 06610003-5, 06610002-5, 06614510-2, 15-200-0062, Wavemaster 7000 (33145 - 1.0HP), C55CXFBY-2918 (Motor Only; Must verify Wet End), 06210049-2 (Watkins), 06614000-5 (Freeflow), C55SWGYA-3860 (Motor Only; Must verify Wet End), Watkins Wavemaster 38944, Watkins 38944, 06115852-1, 06610510-2, 06610000-2, Watkins 77407, 1431701-01 (Watkins), 5KCP112EXP0012X (Motor Only; Must verify Wet End), 48WUA1001C-II (LX / Energy-Rite Pump), 06110510-2, 91231606 (Suction Cover, Faceplate)

This XP2 Pump is also the replacement option for the "Relia-Flo" pumps by Caldera Spas. Verify motor amp rating and voltage, the pump discharge type and size fitting to match. Note that the new motor will not have the back end cover with heat vent/exhaust connection. In case the original motor does have it, the original motor back end cover with heat vent connection may be installed on the new motor if it fits. Otherwise retrofitting a heat vent onto the new motor is required only if it is needed.

This item comes with a 2-year manufacturer's limited warranty.