Hi-Flo 48Y 1.5HP 220V 2SPD SD Waterway Spa Pump Replacement, 2.0-inch

Replacement for the Waterway Hi-Flo Model, 48-frame, 2-speed, Side Discharge Spa Pump, Rated 1.5 horsepower 220V. This pump has a 2.0 inch Center Suction, and a 2.0 inch Side Discharge.

NOTE 1: Pump Unions with O-Rings are sold separately. 

NOTE 2: The pump photo shown to the right does not show a capacitor mounted on top of the motor. We cannot guarantee if the motor that is shipped will or will not have the capacitor attached on top of the motor. Make sure there is plenty of room under the spa for a motor with 6 inches long x 2.5 inches tall x 2.25 inches wide capacitor on top of the motor.

SpaGuts P/N: 15-350-2160

Features:

• Rated 1.5HP SPL, 220V, 8.0/2.6A (*Amp Rating Varies)
• Dual Speed Pump (Low/High. Can also be wired for single speed)
• 2.0-inch center suction, and 2.0-inch side discharge (Outside thread measures approximately 3.1 inch)
• UL and CUL certifications
• Equipped with the highest quality Viton Pump Seal
• Equipped with the high efficiency electrical motor and high performance pump wet end
• Includes a 1-Year limited warranty

*NOTE 3: Amp rating and dimensions may vary depending on the motor brand and model that is used with this pump. Motor brand can be US Motors, AO Smith Century Laser, GE, Etc... If space is very limited for the new pump, contact us to verify dimensions.

The pump image shows the pump discharge on top pointing to the 12 o'clock position. The pump discharge can also be rotated every 90-degrees (3, 6 or 9 o'clock positions) by loosening the four long bolts at the back of the motor. The pump intake (suction) is located in the front center face of the pump.

The pump normally ships from the factory with the discharge pointing "UP" which is the standard position for shipping, but they can be turned or what is called "clocked" into any position (12, 3, 9 or 6 o'clock position). Rotation of the pump discharge can be done in the field, but we recommend having it performed by a professional spa technician who is experienced. This is to avoid water leaks and operational problems due to improper removal and installation in the field that will affect the warranty. As you face the front end of the pump wet end, available positions are 12 o'clock (Up), 3 o'clock (Right), 9 o'clock (Left), and 6 o'clock (Down, which is very rare).

*Looking for a Side Discharge Pump with standard 1.5 inch threaded fittings? CLICK HERE

If buying this pump as an exact replacement that does not require retrofitting, it is highly recommended to replace the pump union o-rings at the same time. Old pump union o-rings may cause leaks that can damage the new pump and affect the warranty.

Keep in mind that if your pump is rated 56-frame, you might want to consider the 56-frame Pump

Is Your Pump Above the Water Line?

If you need to install your spa pump near or above the waterline - as is common for in-ground spas - you will need a PUMP POT. The pump pot help prevents water from draining back into the spa when the motor is turned off.

The Side Discharge Pump is a replacement option for the following Waterway Hi-Flo and Hi-Flo II pump model and part numbers: Waterway 3420620-10 Pump, Waterway 3410612-10 Pump (1SPD), Waterway 3420620-H10 Pump, Waterway 3410612-H10 Pump (1SPD),  Waterway SD-20-2N22CD Pump, Waterway 342062A-10 Pump, Waterway 3420620-10B Pump, SpaGuts 15-350-2160.

Motor Models that are normally used with these pumps: F48AD44A79