Waterway Spa Pump, Executive 56 model, 4.0HP 220V 2-Speed Side Discharge with 2.0" Intake. OEM part number 3721621-1D.
SpaGuts P/N: 15-350-0040
- 220V 60Hz 12.0/4.4A (Amp Rating is Approximate)
- RPM 3450/1725
- 2.0" Center Suction, and 2.0" Side Discharge (Outside thread measures approximately 3.1 inch)
- Dual Speed Pump (can also be wired for single speed)
- 56-Frame Motor for added strength, cooler operating temperature and longer motor life
- Split Capacitor, (start and run) for less energy consumption
- Thermally protected to extend life expectancy of motor
- UL and CUL certifications
- Equipped with the highest quality Viton Pump Seal
- Equipped with the high efficiency electrical motor and high
performance pump wet end
- One year manufacturer's limited warranty on motor and wet end
NOTE: Amp rating and dimension may vary slightly depending on the motor brand that is used with this pump. Motor brand can be US Motors, AO Smith Century Laser, GE, Etc...
The pump image shows the pump discharge on top pointing to the 12 o'clock position. The pump discharge can also be rotated every 90-degrees (3, 6 or 9 o'clock positions) by loosing the four long bolts at the back of the motor. The pump intake (suction) is located in the front center face of the pump.
If buying this pump for retrofitting, add a pair of pump unions that connects to your pipes which then screws directly onto the pump threaded fittings. O-rings are included with the pump unions. Regular price is $15.55.
If buying this pump as an exact replacement that does not require retrofitting, it is highly recommended to replace the pump union o-rings at the same time. Old pump union o-rings may cause leaks that can damage the new pump and affect the warranty. O-rings for pump unions are only available with a pump union purchase.
You may add a cord to be attached to the motor at a discounted price. See cord options below.
The pump normally ships from the factory with the discharge pointing "UP" which is the standard position for shipping, but they can be turned or what is called "clocked" into any position (12, 3, 9 or 6 o'clock position). Rotation of the pump discharge can be done in the field, but we recommend having it performed by a professional spa technician who is experienced. Or choose the option to have the pump professionally rotated at the factory before it ships. This is to avoid water leaks and operational problems due to improper removal and installation in the field that will affect the warranty. As you face the front end of the pump wet end, available positions are 12 o'clock (Up), 3 o'clock (Right), 9 o'clock (Left), and 6 o'clock (Down, which is very rare).
This 56-Frame pump is also a replacement option for the following pumps (Just match the size fittings and amp rating to get the same performance pump): Aquastorm by Infinity Spas, Massage Master XLT, Super-Flo, PF-40-2N22C, 3721621-0D76, X320505, X320500 (1-Speed), 420425, 420469, 420428, 104464, 3711621-1D (1-Speed), P240E52024, PF-40-2N22M, PF-30-2N22C, PF-30-2N22M, PF-30-2N22MC, 3721621-0D36, 3721621-0D, 15-350-2196, 372162A-1D, PF-40-2NCG5, 3721621-0D, 3721621-03, PF-40-2-RV22C, PF-35-2N22C, Massage Master XLT, 3721621-0D76, BX4105-S2, PF451N22C, Master Spa 3711625-0D8PMR, 3721621-0DHB, 3711621-0D6Z (1-Speed), 3M21621-0D, 3721625-0D8QMR, 3411121-0A86 (1-Speed), 3M21621-0T7GDY, 3721628-0D6Y
This pump normally uses the following motor part numbers: 0-187563-02, 5KCP49UN9096X, R63MWENA-4727
Keep in mind to not over power your spa by going from a 48-frame motor
to a 56-frame motor. See water flow chart and amp rating for a 56-frame
Is Your Pump Above the Water Line?
If you need to install your spa pump near or above the waterline - as is
common for in-ground spas - you will need a pump pot.
The pump pot help prevents water from draining back
into the spa when the motor is turned off