Gemini Plus II Variable Spd Bath Pump, NO Switch, 1.5HP 110V 12.5A, 0059F88C, 0059F00C (Special Order)

Gemini Plus II Variable Speed Bath Pump, NO Air Switch, Model NR4-C, by Balboa. Rated 1.5HP, 110V, 12.5A, 1.5 inch.  OEM part numbers 0059F00C and 0059F88C.

This bath pump must be used with a controller or a switch.

SPECIAL ORDER NOTES: THIS ITEM IS A SPECIAL ORDER AND HAS AN ESTIMATED 2-10 BUSINESS DAYS LEAD TIME BEFORE SHIPPING. SPECIAL ORDERS ARE NON-RETURNABLE AND CANNOT BE CANCELED ONCE THE ORDER IS PLACED.

SpaGuts P/N:  16-175-0059

This bath pump is also a replacement option for the following bath pump part numbers:  0060F88C (w/ built-in Air Switch), NR4A-C, 1-00-0221, 34-109-1040, A014E88C, 0014F88C, 0045E88C, 0065F88CC, 5151-211, 0059F88C (no air switch), NL74620DB, Hydro Air NRU2A-C, NR4-C, NRU4-C, 006OF88C, R125A-C, R150VS11C/0072E00C (Obsolete - A new variable speed controller and topside will be needed), 0059F00C / 0059F88C (No Air Switch)

Also a replacement option for the ITT Marlow brand bath pumps.

Failed whirlpool jetted bath tub pumps can be easily replaced with the Gemini Plus II Variable Speed Bath Pump, which fits all whirlpool bath tubs.

The Gemini Plus II Variable Speed Bath Pump is compact and easy to install. It runs quietly.  It’s also known to be the most reliable bath tub pump on the market, with a failure rate of less than 0.1%.

If you are replacing an existing bath tub pump, you should replace it with the same or similar horsepower and amp rating as your existing pump, if you are happy with current forcefulness of the water coming out of your jets.  Check the markings on the pump you are replacing. In general, bathtub pump motors should have 1 HP for every 4 to 6 standard size jets.  More horsepower is not better.  Overpowering your jets with too much horsepower could damage your plumbing, your equipment, or even you!  So, it is important to get the right sized motor for your bath tub.  We offer the following horsepower levels:

For retrofitting, you have the option to add screw-on pump unions which glue directly onto 1.5 inch plumbing.  After the unions are glued onto your bath tub’s existing plumbing, the unions screw directly onto the pump’s suction and return fittings.  The included o-rings provide a tight seal.

Control Options (Sold Separately)

• Add a 20 minute Bath Pump Control to prevent endless run time, and for on/off operation
• Or add the Titan Variable Speed Bath Pump Controller Kit with Topside, 99774 for full control of the bath pump

Options

Heater

Keep your water hot. Add a bath tub heater.

Bath Tub Heater

 

Bathtub Pump & Heater Controller

Prevent endless running of your pump and heater.

Bathtub Controller

 

Bathtub Water Level Sensor

Prevent damage from spraying water. Ensure your bath tub’s water level is above the jets before allowing the pump to run.

Bathtub Water Level Sensor

Features

• UL Recognized and CSA certified for indoor operation
• Works on 50 and 60Hz electrical ratings
• 1-year limited warranty
• Engineered seal design for maximum liability
• Variable Speed Applications, or can be used for single speed
• New Compact design with quieter operation
• Top center discharge
• 100% Self-draining volute
• Standard 1.5-inch fittings
• Thermally protected
• NEMA Plug with 2.5 foot cord length